Search:

Type: Posts; User: Jeremy; Keyword(s):

Page 1 of 10 1 2 3 4

Search: Search took 0.01 seconds.

  1. Just got $10 off:)

    Just got $10 off:)
  2. Replies
    56
    Views
    78,286

    I have the PAR meter in my possession now.

    I have the PAR meter in my possession now.
  3. Replies
    56
    Views
    78,286

    Please add me to the list. Thanks, Jeremy

    Please add me to the list.
    Thanks, Jeremy
  4. Thread: New to CVR

    by Jeremy hi
    Replies
    24
    Views
    5,749

    I think the best thing to feed a bubble tip...

    I think the best thing to feed a bubble tip anemone is a little mysis shrimp. They are small and easy for the anemone to digest. Usually most places sell it in the frozen cube form. The best thing...
  5. Replies
    52
    Views
    9,667

    I sanded the side so you cannot tell the overflow...

    I sanded the side so you cannot tell the overflow was there anymore. Then, I filled the tank up with water in the garage for a water test. I put the bulkhead in the bottom instead of gluing acrylic...
  6. Replies
    52
    Views
    9,667

    I thought about that but thought it was too risky...

    I thought about that but thought it was too risky since it isn't a closed loop. I would need rely on a check valve for power outages. Let me know if you're thinking of something else.

    The drain...
  7. Replies
    52
    Views
    9,667

    Well, I got a little crazy with my new dremel...

    Well, I got a little crazy with my new dremel tool and cut out the overflow. I used two thin strips of metal with double sided tape to protect the side or the tank and guide the blade. I haven't...
  8. Replies
    52
    Views
    9,667

    What do you guys think, should I cut out the...

    What do you guys think, should I cut out the built in overflow? If I cut it out I could stack rocks up against that side to hide the marks where it was. It will only fit one 1" pipe that could be...
  9. Replies
    4
    Views
    866

    Ya, I told him about the club and how I found his...

    Ya, I told him about the club and how I found his pump on ebay.
  10. Replies
    4
    Views
    866

    Thanks, $81 the guy lives in Bako and brought it...

    Thanks, $81 the guy lives in Bako and brought it over to my house :)
  11. Replies
    52
    Views
    9,667

    I finally put the overflow on the tank today. ...

    I finally put the overflow on the tank today.

    I also rounded the bottom outside edge of the slots so the water will roll over and down the side into the box.
    ...
  12. Replies
    52
    Views
    9,667

    Some new stuff came in the mail today. The 1.5"...

    Some new stuff came in the mail today. The 1.5" gate valve is huge. I might need to think about a bigger return pump now that I have multiple large drains.
    ...
  13. Replies
    52
    Views
    9,667

    Today, was my first time cutting acrylic with a...

    Today, was my first time cutting acrylic with a router. I bought the bit today at Lowes. The brand is Bosch and it cuts 1/2" with a bearing on the end. It has a 1/4" shank but the sell 1/2" too. ...
  14. Replies
    52
    Views
    9,667

    Today, I pickup up some acrylic to make my...

    Today, I pickup up some acrylic to make my external overflow box. I haven't really worked with acrylic before but it turned out good so far. Here are some circles I cut out with a router for the...
  15. Replies
    52
    Views
    9,667

    Jesse the overflow is for a 1" schedule 80...

    Jesse the overflow is for a 1" schedule 80 bulkhead. The hole is 1 7/8" and the overflow id is 3"X5". I don't know of a 1.5" bulkhead that can fit inside a 3" overflow box.
  16. Replies
    52
    Views
    9,667

    I've really thought about leaving it how it is...

    I've really thought about leaving it how it is but I think I will always wish I changed it. I'm really thinking about adding an external box with a slot cut in one side for the weir. Here are some...
  17. Replies
    52
    Views
    9,667

    Now, I need to figure out how I'm going to set up...

    Now, I need to figure out how I'm going to set up the tank. The tank has one black overflow box on one end. Both ends are made of black 1/2" acrylic. The bottom of the tank is drilled for a 1.5"...
  18. Replies
    52
    Views
    9,667

    Thanks for all the compliments. Today, I cut...

    Thanks for all the compliments.

    Today, I cut out the plywood and glued up two of the doors. I don't have enough clamps to do all four at once. Hopefully, I can finish the small doors tomorrow....
  19. Replies
    52
    Views
    9,667

    I cut and routed all the rails and stiles for the...

    I cut and routed all the rails and stiles for the doors. Now, I need to cut out some 1/4" plywood and glue them up.

    http://i264.photobucket.com/albums/ii192/zaraemna/rails-and-stiles.jpg
  20. Replies
    52
    Views
    9,667

    I made the front face today. I used a pocket...

    I made the front face today. I used a pocket hole jig to put it together. It's a lot faster than using clamps.
    http://i264.photobucket.com/albums/ii192/zaraemna/Building-faceplate.jpg

    I also...
  21. Replies
    52
    Views
    9,667

    My son and I just got done with our first...

    My son and I just got done with our first pinewood derby. He ended up getting most artistic and first place!

    We called it the Battle Ax....
  22. Replies
    52
    Views
    9,667

    Most of it will be in the room. I'm going to...

    Most of it will be in the room. I'm going to build a wood faceplate for the side by the front door with cabinet doors mounted to it. The face plate will be a frame for the tank too. This way if I...
  23. Replies
    52
    Views
    9,667

    Jeremy's 150+ in wall build

    The tank is 61" x 26" x 24" tall. It is made of 1/2" acrylic and has black ends. There is one overflow on one end of the tank. I'm still trying to decide if I want to add another overflow to the...
  24. Thread: Kalkwasser

    by Jeremy hi
    Replies
    9
    Views
    2,375

    You can't use baking soda either:)

    You can't use baking soda either:)
  25. Replies
    11
    Views
    2,020

    Did you get that one from John?

    Did you get that one from John?
Results 1 to 25 of 245
Page 1 of 10 1 2 3 4